As cerâmicas ácido-resistentes como a zircônia tetragonal parcialmente estabilizada com ítria (Y-TZP), podem ter melhorada sua resistência de união ao cimento resinoso por meio de abrasão por jateamento de partículas. Entretanto, não existe uma padronização dos parâmetros utilizados nesse jateamento, o que pode afetar negativamente o comportamento mecânico da Y-TZP. O objetivo deste estudo foi buscar, através de uma revisão da literatura, quais são os protocolos de jateamento utilizados e qual protocolo resulta em melhores valores de resistência de união ao cimento resinoso e menor degradação das propriedades mecânicas da Y-TZP. A estratégia de pesquisa envolveu uma busca de artigos na base de dados online Medline/Pubmed, de 2003 a 2013, utilizando as palavras chaves: zircônia, adesão, jateamento e resistência mecânica (zirconia, bond strength, sandblasting, and mechanical strength). Foram selecionados vinte e cinco artigos, que estavam de acordo com os critérios de inclusão. O tamanho de partícula mais utilizado foi de 50 µm para partículas de óxido de alumínio e de 110 µm para as partículas de óxido de alumínio modificadas por sílica. Segundo os estudos, o tamanho de partícula e o tempo de jateamento não influenciam os valores de resistência de união. Entretanto, o maior tamanho e o tipo de partícula (óxido de alumínio) afetam negativamente a resistência mecânica da Y-TZP. Ainda existem controvérsias a respeito do efeito da pressão na resistência de união e na resistência mecânica da Y-TZP. O uso de pressões muito baixas pode afetar os valores de adesão. A distância entre a ponta jateadora e a superfície cerâmica e o tempo variou entre 7 a 30 mm e 5 a 90 s, respectivamente. Pôde-se concluir que alguns parâmetros do protocolo de jateamento ainda não estão bem definidos. Mesmo assim, os resultados dos estudos parecem corroborar a recomendação do uso de partículas pequenas e pressões baixas para alcançar o melhor resultado de adesão sem comprometer a resistência mecânica do material.
The bond strength of acid-resistant ceramics, such as yttria partially stabilized tetragonal zirconia (Y-TZP), to resin cements could be improved by surface sandblasting with particles. However, there is not a standard protocol for sandblasting, which may compromise Y-TZP mechanical behavior. The objective of this study was to search, trough a literature review, which sandblasting protocols have been used and which one results in higher bond strength values of Y-TZP to resin cement and less degradation of the mechanical properties of Y-TZP. The research involved articles published from 2003 to 2013 using Medline/Pubmed online database and the keywords: zirconia, bond strength, sandblasting, and mechanical strength. Twenty five articles that were within the study inclusion criteria were selected. The particle size most frequently used was 50 µm for aluminum oxide and 30 µm for silica-modified aluminum oxide. According to the literature, the particle size and sandblasting time have no influence on the bond strength values. On the other hand, the larger particle size and the particle type (aluminum oxide) negatively affected the Y-TZP mechanical strength. There are disagreements regarding the effects of sandblasting pressure on the bond and Y-TZP mechanical strength. The use of extremely low pressures may decrease the bond strength values. The distance from the tip of the sandblasting device and the ceramic surface, and the sandblasting time, varied from 7 to 30 mm and 5 to 90 s, respectively. It can be concluded that some of the sandblasting parameters are not yet clearly defined. Even though, the results of studies seem to confirm the recommendation of using small particles and low sandblasting pressures to achieve superior bond strength without decreasing the material mechanical strength.