13
views
0
recommends
+1 Recommend
0 collections
    0
    shares
      • Record: found
      • Abstract: found
      • Article: found
      Is Open Access

      Red blood cell phase separation in symmetric and asymmetric microchannel networks: effect of capillary dilation and inflow velocity

      research-article

      Read this article at

      Bookmark
          There is no author summary for this article yet. Authors can add summaries to their articles on ScienceOpen to make them more accessible to a non-specialist audience.

          Abstract

          The non-uniform partitioning or phase separation of red blood cells (RBCs) at a diverging bifurcation of a microvascular network is responsible for RBC heterogeneity within the network. The mechanisms controlling RBC heterogeneity are not yet fully understood and there is a need to improve the basic understanding of the phase separation phenomenon. In this context, in vitro experiments can fill the gap between existing in vivo and in silico models as they provide better controllability than in vivo experiments without mathematical idealizations or simplifications inherent to in silico models. In this study, we fabricated simple models of symmetric/asymmetric microvascular networks; we provided quantitative data on the RBC velocity, line density and flux in the daughter branches. In general our results confirmed the tendency of RBCs to enter the daughter branch with higher flow rate (Zweifach-Fung effect); in some cases even inversion of the Zweifach-Fung effect was observed. We showed for the first time a reduction of the Zweifach-Fung effect with increasing flow rate. Moreover capillary dilation was shown to cause an increase of RBC line density and RBC residence time within the dilated capillary underlining the possible role of pericytes in regulating the oxygen supply.

          Related collections

          Most cited references40

          • Record: found
          • Abstract: found
          • Article: not found

          Soft lithography in biology and biochemistry.

          Soft lithography, a set of techniques for microfabrication, is based on printing and molding using elastomeric stamps with the patterns of interest in basrelief. As a technique for fabricating microstructures for biological applications, soft lithography overcomes many of the shortcomings of photolithography. In particular, soft lithography offers the ability to control the molecular structure of surfaces and to pattern the complex molecules relevant to biology, to fabricate channel structures appropriate for microfluidics, and to pattern and manipulate cells. For the relatively large feature sizes used in biology (> or = 50 microns), production of prototype patterns and structures is convenient, inexpensive, and rapid. Self-assembled monolayers of alkanethiolates on gold are particularly easy to pattern by soft lithography, and they provide exquisite control over surface biochemistry.
            Bookmark
            • Record: found
            • Abstract: found
            • Article: not found

            Blood flow in microvascular networks. Experiments and simulation.

            A theoretical model has been developed to simulate blood flow through large microcirculatory networks. The model takes into account the dependence of apparent viscosity of blood on vessel diameter and hematocrit (the Fahraeus-Lindqvist effect), the reduction of intravascular hematocrit relative to the inflow hematocrit of a vessel (the Fahraeus effect), and the disproportionate distribution of red blood cells and plasma at arteriolar bifurcations (phase separation). The model was used to simulate flow in three microvascular networks in the rat mesentery with 436,583, and 913 vessel segments, respectively, using experimental data (length, diameter, and topological organization) obtained from the same networks. Measurements of hematocrit and flow direction in all vessel segments of these networks tested the validity of model results. These tests demonstrate that the prediction of parameters for individual vessel segments in large networks exhibits a high degree of uncertainty; for example, the squared coefficient of correlation between predicted and measured hematocrit of single vessel segments ranges only between 0.15 and 0.33. In contrast, the simulation of integrated characteristics of the network hemodynamics, such as the mean segment hematocrit or the distribution of blood flow velocities, is very precise. In addition, the following conclusions were derived from the comparison of predicted and measured values: 1) The low capillary hematocrits found in mesenteric microcirculatory networks as well as their heterogeneity can be explained on the basis of the Fahraeus effect and phase-separation phenomena. 2) The apparent viscosity of blood in vessels of the investigated tissue with diameters less than 15 microns is substantially higher than expected compared with measurements in glass tubes with the same diameter.
              Bookmark
              • Record: found
              • Abstract: found
              • Article: not found

              Surface molecular property modifications for poly(dimethylsiloxane) (PDMS) based microfluidic devices

              Fast advancements of microfabrication processes in past two decades have reached to a fairly matured stage that we can manufacture a wide range of microfluidic devices. At present, the main challenge is the control of nanoscale properties on the surface of lab-on-a-chip to satisfy the need for biomedical applications. For example, poly(dimethylsiloxane) (PDMS) is a commonly used material for microfluidic circuitry, yet the hydrophobic nature of PDMS surface suffers serious nonspecific protein adsorption. Thus the current major efforts are focused on surface molecular property treatments for satisfying specific needs in handling macro functional molecules. Reviewing surface modifications of all types of materials used in microfluidics will be too broad. This review will only summarize recent advances in nonbiofouling PDMS surface modification strategies applicable to microfluidic technology and classify them into two main categories: (1) physical approach including physisorption of charged or amphiphilic polymers and copolymers, as well as (2) chemical approach including self assembled monolayer and thick polymer coating. Pros and cons of a collection of available yet fully exploited surface modification methods are briefly compared among subcategories.
                Bookmark

                Author and article information

                Journal
                Sci Rep
                Sci Rep
                Scientific Reports
                Nature Publishing Group
                2045-2322
                18 November 2016
                2016
                : 6
                : 36763
                Affiliations
                [1 ]ARTORG Center, University of Bern , Bern, Switzerland
                [2 ]Haute Ecole Arc Ingénierie, HES-SO // University of Applied Sciences Western Switzerland, La Chaux-de-Fonds , Switzerland
                Author notes
                Article
                srep36763
                10.1038/srep36763
                5114676
                27857165
                d4202170-10bc-42f1-8c36-363c00b27a5f
                Copyright © 2016, The Author(s)

                This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/

                History
                : 25 July 2016
                : 20 October 2016
                Categories
                Article

                Uncategorized
                Uncategorized

                Comments

                Comment on this article