28
views
0
recommends
+1 Recommend
1 collections
    1
    shares
      • Record: found
      • Abstract: found
      • Article: found

      Adjustment of Lifetime-Increasing Surface Layer States by Complementary Machining∗ Translated title: Einstellung lebensdauersteigernder Randschichtzustände durch Komplementärzerspanung

      research-article

      Read this article at

      ScienceOpenPublisher
      Bookmark
          There is no author summary for this article yet. Authors can add summaries to their articles on ScienceOpen to make them more accessible to a non-specialist audience.

          Abstract

          During manufacturing of metallic components, thermo-mechanical loadings induce surface layer states like topography or residual stresses, which influence the component properties like fatigue strength. In order to optimize the component properties, a mechanical surface treatment can be carried out after the machining process. In this work, the influence of the process parameters processing velocity and penetration depth on the resulting tool wear during external longitudinal turning of AISI 4140q&t by Complementary Machining is analyzed. The process strategy Complementary Machining (CM) combines machining and mechanical surface treatment using the cutting tool. The mechanical surface treatment takes place after the machining in the opposite machining direction. The results of this study show that the process variables have an influence on the tool wear and thus directly influence the resulting topography. The fatigue analysis shows that the fatigue strength after Complementary Machining is comparable to that of shot peening. Furthermore, the concept of local fatigue strength is used to show the extent that residual stress reduction as a result of cyclic loading affects the fatigue strength.

          Kurzfassung

          Bei der Herstellung metallischer Bauteile beeinflussen die wirkenden thermo-mechanischen Lastkollektive die Randschichtzustände wie z. B. Topographie oder Eigenspannungen, welche wiederum die Bauteileigenschaften wie die Schwingfestigkeit beeinflussen. Zur Optimierung der Randschichtzustände kann nach dem Zerspanungsprozess eine mechanische Oberflächenbehandlung durchgeführt werden. In dieser Studie wird der Einfluss der Prozessstellgrößen Bearbeitungsgeschwindigkeit und -tiefe auf den Werkzeugverschleiß bei der Komplementärzerspanung im Außenlängsdrehen am Beispiel des Vergütungsstahls 42CrMo4 analysiert. Die Komplementärzer-spanung kombiniert die Zerspanung mit der mechanischen Oberflächenbehandlung unter Verwendung des Zerspanungswerkzeugs, indem nach der Zerspanung in entgegengesetzter Bearbeitungsrichtung die mechanische Oberflächenbehandlung erfolgt. Die Ergebnisse zeigen, dass die Prozessstellgrößen Einfluss auf den einsetzenden Werkzeugverschleiß haben und damit unmittelbar die resultierende Topographie beeinflussen. Die Schwingfestigkeitsanalyse zeigt, dass die Schwingfestigkeit nach der Komplementärzerspanung vergleichbar mit der beim Kugelstrahlen ist. Weiterhin wird anhand des Konzepts der lokalen Dauerfestigkeit vorgestellt, inwieweit sich der Eigenspannungsabbau infolge zyklischer Belastung auf die Wechselfestigkeit auswirkt.

          Most cited references21

          • Record: found
          • Abstract: not found
          • Article: not found

          Surface integrity in material removal processes: Recent advances

            Bookmark
            • Record: found
            • Abstract: not found
            • Article: not found

            Micro-dimpled surface by ultrasonic nanocrystal surface modification and its tribological effects

              Bookmark
              • Record: found
              • Abstract: not found
              • Article: not found

              Surface improvement of shafts by the deep ball-burnishing technique

                Bookmark

                Author and article information

                Journal
                htme
                HTM Journal of Heat Treatment and Materials
                Carl Hanser Verlag
                1867-2493
                2194-1831
                14 June 2019
                : 74
                : 3
                : 181-190
                Affiliations
                1 wbk Institut für Produktionstechnik, Karlsruher Institut für Technologie (KIT), Kaiserstr. 12, 76131 Karlsruhe, Germany
                2 Fakultät für Maschinenbau, Karlsruher Institut für Technologie (KIT), Karlsruhe, Germany
                3 wbk Institut für Produktionstechnik, Karlsruher Institut für Technologie (KIT), Karlsruhe, Germany
                Author notes
                [∗]

                Lecture presented at the HeatTreatmentCongress, HK 2018, October 16–18, 2018, Cologne, Germany

                4 michael.gerstenmeyer@ 123456kit.edu (Corresponding author/Kontakt)
                Article
                HT110376
                10.3139/105.110376
                f487d64e-ebd1-4d4f-959f-30d79183835b
                © 2019, Carl Hanser Verlag, München
                History
                Page count
                References: 26, Pages: 10
                Categories
                Scientific Contributions/Fachbeiträge

                Materials technology,Materials characterization,General engineering,Mechanical engineering,Materials science
                Complementary Machining,Machining,mechanical surface treatment,surface layer states,fatigue strength,Zerspanung,mechanische Oberflächenbehandlung,Randschichtzustände,Lebensdauer,Komplementärzerspanung

                Comments

                Comment on this article