NanoRelease: Pilot interlaboratory comparison of a weathering protocol applied to resilient and labile polymers with and without embedded carbon nanotubes

There is no author summary for this article yet. Authors can add summaries to their articles on ScienceOpen to make them more accessible to a non-specialist audience.

Abstract

A major use of multi-walled carbon nanotubes (MWCNTs) is as functional fillers embedded in a solid matrix, such as plastics or coatings. Weathering and abrasion of the solid matrix during use can lead to environmental releases of the MWCNTs. Here we focus on a protocol to identify and quantify the primary release induced by weathering, and assess reproducibility, transferability, and sensitivity towards different materials and uses. We prepared 132 specimens of two polymer-MWCNT composites containing the same grade of MWCNTs used in earlier OECD hazard assessments but without UV stabilizer. We report on a pilot inter-laboratory comparison (ILC) with four labs (two US and two EU) aging by UV and rain, then shipping for analysis. Two labs (one US and one EU) conducted the release sampling and analysis by Transmission Electron Microscopy (TEM), Inductively Coupled Plasma- Mass Spectrometry (ICP-MS), UltravioleteVisible Spectroscopy (UVeVis), Analytical Ultracentrifugation (AUC), and Asymmetric Flow Field Flow Fractionation (AF4). We compare results between aging labs, between analysis labs and between materials. Surprisingly, we found quantitative agreement between analysis labs for TEM, ICP-MS, UVeVis; low variation between aging labs by all methods; and consistent rankings of release between TEM, ICP-MS, UVeVis, AUC. Significant disagreement was related primarily to differences in aging, but even these cases remained within a factor of two.

Related collections

Most cited references 35

Record: found
Abstract: found
Article: not found

Review of nanomaterial aging and transformations through the life cycle of nano-enhanced products.

Denise M Mitrano, Sylvie Motellier, Simon Clavaguera … (2015)

In the context of assessing potential risks of engineered nanoparticles (ENPs), life cycle thinking can represent a holistic view on the impacts of ENPs through the entire value chain of nano-enhanced products from production, through use, and finally to disposal. Exposure to ENPs in consumer or environmental settings may either be to the original, pristine ENPs, or more likely, to ENPs that have been incorporated into products, released, aged and transformed. Here, key product-use related aging and transformation processes affecting ENPs are reviewed. The focus is on processes resulting in ENP release and on the transformation(s) the released particles undergo in the use and disposal phases of its product life cycle for several nanomaterials (Ag, ZnO, TiO2, carbon nanotubes, CeO2, SiO2 etc.). These include photochemical transformations, oxidation and reduction, dissolution, precipitation, adsorption and desorption, combustion, abrasion and biotransformation, among other biogeochemical processes. To date, few studies have tried to establish what changes the ENPs undergo when they are incorporated into, and released from, products. As a result there is major uncertainty as to the state of many ENPs following their release because much of current testing on pristine ENPs may not be fully relevant for risk assessment purposes. The goal of this present review is therefore to use knowledge on the life cycle of nano-products to derive possible transformations common ENPs in nano-products may undergo based on how these products will be used by the consumer and eventually discarded. By determining specific gaps in knowledge of the ENP transformation process, this approach should prove useful in narrowing the number of physical experiments that need to be conducted and illuminate where more focused effort can be placed.

0 comments Cited 92 times – based on 0 reviews      Review now

Bookmark

Record: found
Abstract: found
Article: not found

Reactivity of carbon nanotubes: free radical generation or scavenging activity?

Maura Tomatis, B. Nagy, Antônio Fonseca … (2006)

Carbon nanotubes (CNTs) currently attract intense research efforts because of their unique properties which make them suitable for many industrial applications. When inhaled, CNTs constitute a possible hazard to human health. Several studies have shown that when instilled in the lung of experimental animals, CNTs induced an inflammatory and fibrotic response similar to that caused by other toxic particles which might be the result of oxidative stress caused by particle- and/or cell-derived free radicals. There is, however, no direct experimental evidence of a capacity of carbon nanotubes to generate directly free radicals. Here we report that multiwall carbon nanotubes (MWCNT) in aqueous suspension do not generate oxygen or carbon-centered free radicals in the presence of H2O2 or formate, respectively, as detected with the spin-trapping technique. Conversely, we observed that, when in contact with an external source of hydroxyl or superoxide radicals, MWCNT exhibit a remarkable radical scavenging capacity. It is therefore possible that the inflammatory reaction reported in vivo must be ascribed to MWCNT features other than particle-derived free radical generation.

0 comments Cited 49 times – based on 0 reviews      Review now

Bookmark

Record: found
Abstract: found
Article: not found

Is Open Access

Potential release scenarios for carbon nanotubes used in composites.

Bernd Nowack, Aaron J. Shatkin, Inge D Brouwer … (2013)

The expected widespread use of carbon nanotube (CNT)-composites in consumer products calls for an assessment of the possible release and exposure to workers, consumers and the environment. Release of CNTs may occur at all steps in the life cycle of products, but to date only limited information is available about release of CNTs from actual products and articles. As a starting point for exposure assessment, exploring sources and pathways of release helps to identify relevant applications and situations where the environment and especially humans may encounter releases of CNTs. It is the aim of this review to identify various potential release scenarios for CNTs used in polymers and identify the greatest likelihood of release at the various stages throughout the life-cycle of the product. The available information on release of CNTs from products and articles is reviewed in a first part. In a second part nine relevant release scenarios are described in detail: injection molding, manufacturing, sports equipment, electronics, windmill blades, fuel system components, tires, textiles, incineration, and landfills. Release from products can potentially occur by two pathways; (a) where free CNTs are released directly, or more frequently (b) where the initial release is a particle with CNTs embedded in the matrix, potentially followed by the subsequent release of CNTs from the matrix. The potential for release during manufacturing exists for all scenarios, however, this is also the situation when exposure can be best controlled. For most of the other life cycle stages and their corresponding release scenarios, potential release of CNTs can be considered to be low, but it cannot be excluded totally. Direct release to the environment is also considered to be very low for most scenarios except for the use of CNTs in tires where significant abrasion during use and release into the environment would occur. Also the possible future use of CNTs in textiles could result in consumer exposure. A possibility for significant release also exists during recycling operations when the polymers containing CNTs are handled together with other polymers and mainly occupational users would be exposed. It can be concluded that in general, significant release of CNTs from products and articles is unlikely except in manufacturing and subsequent processing, tires, recycling, and potentially in textiles. However except for high energy machining processes, most likely the resulting exposure for these scenarios will be low and to a non-pristine form of CNTs. Actual exposure studies, which quantify the amount of material released should be conducted to provide further evidence for this conclusion. Copyright © 2013 The Authors. Published by Elsevier Ltd.. All rights reserved.

0 comments Cited 48 times – based on 0 reviews      Review now

Bookmark

All references

Author and article information

Journal

Journal ID (nlm-journal-id): 101204394

Journal ID (pubmed-jr-id): 31886

Journal ID (nlm-ta): Carbon N Y

Journal ID (iso-abbrev): Carbon N Y

Title: Carbon

ISSN (Print): 0008-6223

Publication date Nihms-submitted: 31 July 2018

Publication date (Print): March 2017

Publication date PMC-release: 22 August 2018

Volume: 113

Pages: 346-360

Affiliations

[a ]BASF SE, Dept. Material Physics and Analytics, 67056, Ludwigshafen, Germany

[b ]National Research Council Canada, Ottawa, Canada

[c ]Occupational Safety and Health Administration (OSHA), USA

[d ]U.S. Environmental Protection Agency (EPA), Office of Research and Development (ORD), National Risk Management Research Laboratory (NRMRL), Cincinnati, OH, USA

[e ]LEITAT Technological Center, C7 de la Innovació 2, 08225, Terrassa, Barcelona, Spain

[f ]EPA, ORD, National Exposure Research Laboratory (NERL), 960 College Station Rd., Athens, GA, USA

[g ]EPA, Region 4, Science and Ecosystem Support Division (SESD), Athens, GA, USA

[1 ]Student Services Associate.

[2 ]National Research Council Associate.

Author notes

[* ]Corresponding author. Zepp.Richard@ 123456epa.gov (R. Zepp).

Article

Manuscript ID: EPAPA983220

DOI: 10.1016/j.carbon.2016.11.011

PMC ID: 6104645

PubMed ID: 30147114

SO-VID: f5a9e9c3-f8dd-4f6a-a335-76ddc4615036

License:

This is an open access article under the CC BY-NC-ND license ( http://creativecommons.org/licenses/by-nc-nd/4.0/).

NanoRelease: Pilot interlaboratory comparison of a weathering protocol applied to resilient and labile polymers with and without embedded carbon nanotubes

Read this article at

Abstract

Related collections

Open Access Publishing Practices

Most cited references 35

Review of nanomaterial aging and transformations through the life cycle of nano-enhanced products.

Reactivity of carbon nanotubes: free radical generation or scavenging activity?

Potential release scenarios for carbon nanotubes used in composites.

Author and article information

Journal

Affiliations

Author notes

Article

History

Categories

Comments

Comment on this article

Similar content 55

Cited by 13

Most referenced authors 363