22
views
0
recommends
+1 Recommend
0 collections
    0
    shares
      • Record: found
      • Abstract: found
      • Article: found
      Is Open Access

      Long-Term Soft Denture Lining Materials

      review-article

      Read this article at

      Bookmark
          There is no author summary for this article yet. Authors can add summaries to their articles on ScienceOpen to make them more accessible to a non-specialist audience.

          Abstract

          Long-term soft denture lining (LTSDL) materials are used to alleviate the trauma associated with wearing complete dentures. Despite their established clinical efficacy, the use of LTSDLs has been limited due to the unfavorable effects of the oral environment on some of their mechanical and performance characteristics. The unresolved issue of LTSDL colonization by Candida albicans is particularly problematic. Silicone-based LTSDL (SLTSDL) materials, which are characterized by more stable hardness, sorption and solubility than acrylic-based LTSDLs (ALTSDLs), are currently the most commonly used LTSDLs. However, SLTSDLs are more prone to debonding from the denture base. Moreover, due to their limitations, the available methods for determining bond strength do not fully reflect the actual stability of these materials under clinical conditions. SLTSDL materials exhibit favorable viscoelastic properties compared with ALTSDLs. Furthermore, all of the lining materials exhibit an aging solution-specific tendency toward discoloration, and the available cleansers are not fully effective and can alter the mechanical properties of LTSDLs. Future studies are needed to improve the microbiological resistance of LTSDLs, as well as some of their performance characteristics.

          Related collections

          Most cited references143

          • Record: found
          • Abstract: found
          • Article: not found

          Retention of Candida albicans on acrylic resin and silicone of different surface topography.

          The adhesion of microorganisms to a denture surface is a prerequisite for colonization. This study compared the retention of Candida albicans on smooth and rough acrylic resin and silicone surfaces after a washing procedure to determine the effect of surface roughness on prosthesis infection and hygiene. Standardized cell suspensions of C. albicans were incubated with smooth and rough acrylic resin and silicone surfaces for 1 hour at 24 degrees C. After washing, cells that had been retained on the surface were stained with acridine orange and examined with incident beam fluorescent microscopy. There was no significant difference in cell numbers on either of the smooth surfaces. Significantly higher numbers of cells (p > 0.0005) were observed on roughened surfaces (silicone > acrylic resin) than on smooth surfaces. The fitting surface of the maxillary denture was not polished. Silicones used in prostheses were processed against dental stone. The resultant surface roughness may facilitate microbial retention and infection and should therefore be kept to a minimum.
            Bookmark
            • Record: found
            • Abstract: found
            • Article: not found

            Prevention and treatment of Candida colonization on denture liners: a systematic review.

            Denture liners are well known for their poor physical properties that favor the accumulation of plaque and colonization by Candida species, which can irritate the oral tissues and lead to denture stomatitis.
              Bookmark
              • Record: found
              • Abstract: found
              • Article: not found

              Assessment of mechanical conditions in sub-dermal tissues during sitting: a combined experimental-MRI and finite element approach.

              A common but potentially severe malady afflicting permanent wheelchair users is pressure sores caused by elevated soft tissue strains and stresses over a critical prolonged period of time. Presently, there is paucity of information regarding deep soft tissue strains and stresses in the buttocks of humans during sitting. Strain and stress distributions in deep muscle and fat tissues were therefore calculated in six healthy subjects during sitting, in a double-donut Open-MR system, using a "reverse engineering" approach. Specifically, finite element (FE) models of the undeformed buttock were built for each subject using MR images taken at the coronal plane in a non-weight-bearing sitting posture. Using a second MR image taken from each subject during weight-bearing sitting we characterized the ischial tuberosity sagging toward the sitting surface in weight-bearing, and used these data as displacement boundary conditions for the FE models. These subject-specific FE analyses showed that maximal tissue strains and stresses occur in the gluteal muscles, not in fat or at the skin near the body-seat interface. Peak principal compressive strain and stress in the gluteus muscle were 74+/-7% and 32+/-9 kPa (mean+/-standard deviation), respectively. Peak principal compressive strain and stress in enveloping fat tissue were 46+/-7% and 18+/-4 kPa, respectively. Models were validated by comparing measured peak interface pressures under the ischial tuberosities (17+/-4 kPa) with those calculated by means of FE (18+/-3 kPa), for each subject. This is the first study to quantify sub-dermal tissue strain and stress distributions in sitting humans, in vivo. These data are essential for understanding the aetiology of pressure sores, particularly those that were recently termed "deep tissue injury" at the US National Pressure Ulcer Advisory Panel (NPUAP) 2005 Consensus Conference.
                Bookmark

                Author and article information

                Journal
                Materials (Basel)
                Materials (Basel)
                materials
                Materials
                MDPI
                1996-1944
                12 August 2014
                August 2014
                : 7
                : 8
                : 5816-5842
                Affiliations
                [1 ]Division of Materials Processing Technology, Institute of Engineering Materials and Biomaterials, Silesian University of Technology, ul. Konarskiego 18a, Gliwice 44-100, Poland; E-Mail: jaroslaw.zmudzki@ 123456polsl.pl
                [2 ]Department of Prosthetic Dentistry, Medical University of Silesia, pl. Akademicki 17, Bytom 41-902, Poland; E-Mail: kroczek91@ 123456interia.pl
                Author notes
                [* ]Author to whom correspondence should be addressed; E-Mail: grzegorz.chladek@ 123456polsl.pl ; Tel.: +48-32-237-29-07.
                Article
                materials-07-05816
                10.3390/ma7085816
                5456172
                28788163
                e6a2c6c8-d7e7-4f54-91b9-8c0d7203b700
                © 2014 by the authors.

                Licensee MDPI, Basel, Switzerland. This article is an open access article distributed under the terms and conditions of the Creative Commons Attribution license ( http://creativecommons.org/licenses/by/3.0/).

                History
                : 13 May 2014
                : 31 July 2014
                : 01 August 2014
                Categories
                Review

                dental materials,dentures,polymers,edentulism,soft lining,candida albicans

                Comments

                Comment on this article